Classifieds Business Directory Jobs Real Estate Autos Legal Notices ePubs Subscribe Archives
Today is July 22, 2014
home news sports feature opinion fyi society obits multimedia

Front Page » May 16, 2002 » Castle County Homes and Gar... » Tips for the plumbing emergency
Published 4,450 days ago

Tips for the plumbing emergency


Print PageEmail PageShareGet Reprints


Although you may not feel qualified to take on major plumbing installations or repairs around the house, there are many small things that you can easily do to repair, clean or maintain your plumbing. These simple tips are only ideas, however a licensed plumber should always be contacted to assist with plumbing emergencies.

How do you clear a clogged drain? What do you do to keep a faucet looking and running like new? How do you prepare for a plumbing emergency? What is the best way to clean fixtures? Read on for the answers to those questions as well as tips for maintaining your plumbing.

Be Prepared for a Plumbing Emergency - Homeowners hope they will never have to face a plumbing emergency, but the best time to prepare is before it happens.

"When water is spewing from a broken pipe or creeping slowly towards your carpet is not the time to be hunting for a water shut-off valve," says Mike Pickett, vice president, Product Development at Moen Incorporated. "Our plumbing experts first recommend making a plumbing discovery tour of your home. A few minutes of your time now can provide the assurance you need to handle a crisis down the road."

Make a Plumbing Discovery Tour. A "plumbing discovery tour" involves locating and clearly marking all shut-off valves in your home. First, find the main water shut-off valve. This valve is usually located in the basement on the pipe coming through the wall on the street side of your house (near the water meter). By shutting off this valve, you will shut off water to your entire house, which may be necessary for a serious emergency.

Be aware, though, that if you do shut off the water at the main valve, a gas hot water tank must be turned down to as low possible (find the control on the face of the tank and set it to the "vacation" setting). An electric tank should be shut off at the electrical panel. If you have a hot water heating system, you will also need to check that the furnace has a sufficient supply of water so it does not run dry.

During your tour, you also should note the locations of shut-off valves for other plumbing fixtures. Below your kitchen sink you will most likely find shut-off valves for both hot and cold water. In the bathroom, there are three primary valves operating the faucet, toilet and bathtub/shower. These valves are typically located below the fixtures for easy access, though the tub valve(s) may be in the basement (or behind the bathroom wall in a bedroom closet, for example).

Continue the tour in every room that has a plumbing-related appliance. Be sure to locate, test and tag valves to your washing machine, dishwasher, hot water heating system, water heater, refrigerator ice maker, water softener � every place in the house where water is used.

Check the Condition of Your Valves - It is important to check all valves often since they may become "frozen" from lack of use. A wrench or some WD-40 carefully applied will probably loosen any stuck valves.

Leaks, Clogs and Other Problems - For more serious matters it is usually best to call a plumber, but there are some things you can do yourself to take care of small problems.

Clogged Drain - To clear a clogged drain, first try a plunger. If that does not remove the problem, use a hand auger, which is a flexible steel cable that can be pushed into the drain to break up the obstruction. Your next step of defense is to use a blow bag that hooks to a garden hose and uses water pressure to clear the clog. Use caustic, acid-based chemical drain cleaners only as a last resort since they may damage pipes.

Continuously Running Toilet - If water continuously runs in your toilet, it may be a problem with the float rising too high, causing water to trickle down the overflow tube. To fix this, bend the rod slightly downward so the float ball is lowered. If fixing that doesn't help, see if the trip lever chain is tangled or has fallen off. Next check the tank flapper at the base of the tank and the ballcock, which is located near the top of the tank. These items may have to be cleaned, adjusted or replaced if they have worn out.

Toilet Won't Flush - If a toilet won't flush, it is likely that the chain has slipped off or a new flush-handle assembly is needed. Start by examining the inside of the tank. Is one end of the chain attached to the flush handle and the other to a rubber seal at the bottom? If the chain has slipped off, reattach it. If the handle itself is broken, you will need to replace it with a new assembly.

Leaky Faucet - If you have a cartridge-type faucet, a leak usually indicates that the O-rings need to be replaced. This is a simple repair that even the novice do-it-yourselfer can perform. If the faucet leaks from the handle, the upper O-ring probably needs replacement, while a drip from the spout will indicate a problem with the O-ring at the base of the spout assembly. O-rings also form a seal between the hot and cold supply lines, so be sure to examine these once you have the faucet disassembled. When replacing O-rings, give them a light coating of heatproof lubricant. If replacing O-rings doesn't solve your problems, you may need to replace the cartridge itself.

A ceramic disk faucet that leaks at the base of the handle means that one or more of the inlet seals on the cartridge may need replacing. These seals can be easily replaced. You may also want to clean the inlet ports on this type of faucet since they can become clogged with mineral deposits. A complete cartridge replacement may be needed if leaking problems persist.

A rotating ball faucet is difficult to repair because of its many parts. You should first disassemble the cam, ball and spout to see if there are any problems there - many leaks result from a worn out ball or gasket. If those seem fine, remove seals and springs to check for blockages. Leaks also can spring from around the handle or from under the base of the spout. Handle leaks indicate that the adjusting ring has loosened or the seal above the ball is worn. Leaks from under the spout result from O-ring failure. Examine all O-rings encircling the body of the faucet to see if they look worn.

Hard-to-Move Faucet Handles - If you are having trouble turning your faucet on and off, you probably have a problem with mineral deposits. To solve this problem, simply clean the cartridge and apply a thin film of FSA-approved silicon grease � never use petroleum jelly.

Basic Maintenance of Plumbing Fixtures and Faucets - One of the easiest plumbing fixtures to care for is a faucet � the only things needed for cleaning are some water and a little elbow grease.

"Many people think you need to use a commercial cleansing product to clean a faucet, but the best thing is a soft, damp cloth and warm water," said Pickett.


Print PageEmail PageShareGet Reprints


Top of Page


 
Web Poll  
April 24, 2014
Do you think armed militia and individuals should have joined the protest last weekend concerning the removal of the cattle owned by Cliven Bundy from BLM land in Southern Nevada?
Yes
No
Don't know
Don't care

View Results


Castle County Homes and Gardens  
May 16, 2002
Recent Focus
Quick Links
Subscribe via RSS
Related Articles  
Related Stories



Best viewed with Firefox
Get Firefox

© Sun Advocate, 2000-2013. All rights reserved. All material found on this website, unless otherwise specified, is copyright and may not be reproduced without the explicit written permission from the publisher of the Sun Advocate.
Legal Notices & Terms of Use    Privacy Policy    Advertising Info    FAQ    Contact Us
  RSS Feeds    News on Your Site    Staff Information    Submitting Content    About Us